Sony ICD-P320

Instrukcja obsługi Sony ICD-P320

(1)
  • When playing back a previously recorded message, start from Step 1.
    When playing back a message you have just finished recording, start from Step 3.
    1
    Select the folder.
    See “Selecting the Folder”.
    2
    Select the message number.
    * The display selected with the DISPLAY/MENU button appears (see the reverse side).
    3
    Start playback.
    After playing back one message, the unit stops at the beginning of the next
    message. When the continuous play function is set to “ON” (see the reverse
    side), the unit stops after playing all messages in a folder.
    When the last message on a folder has been played back, the unit stops at the
    beginning of the last message.
    For private listening
    Connect an ear receiver or headphones (not supplied) to the i (earphone) jack.
    The built-in speaker will be automatically disconnected. If noise is heard, wipe
    the headphones plug.
    Other operations
    To Do this
    stop at the current position Press NxPLAY/STOP or xSTOP.
    To resume playback from that point,
    press NxPLAY/STOP again.
    go back to the beginning Press – . once.*
    of the current message
    skip to the next message Press >+ once.*
    go back to previous Press – . or >+ repeatedly.
    messages/skip to succeeding (During stop mode, keep the button
    messages pressed to skip the messages
    continuously.)
    * These operations are for when EASY-S (Easy Search function) of the menu is set to
    “OFF”.
    1
    Slide and lift the battery
    compartment lid.
    2
    Insert two LR03 (size AAA)
    alkaline batteries with
    correct polarity, and close the
    lid.
    Clock setting display appears when you insert batteries for the first time, or or
    when you replace the batteries with new ones. Please refer to Steps 2 to 3 in
    “Step 2: Setting the Clock” to set the date and time.
    IC Recorder
    Operating Instructions
    2005 Sony Corporation Printed in China
    ICD-P320
    Owner’s Record
    The model number is located at the rear and the serial number is located inside the battery
    compartment. Record the serial number in the space provided below. Refer to these numbers
    whenever you call upon your Sony dealer regarding this product.
    Model No. ICD-P320 Serial No. _____________________________________
    Step 1: Installing the Batteries
    Replacing the batteries
    The battery indicator in the display
    window shows the battery
    condition.
    When
    flashes, replace the
    batteries with new ones.
    When
    flashes, the batteries are
    exhausted and the unit will stop
    operation.
    Battery life*
    With continuous use, approx. 11 hours
    recording/7.5 hours playback in the
    HQ mode, and approx. 22 hours
    recording/11 hours playback in the SP
    and LP modes is possible.
    * Using Sony alkaline batteries LR03
    (size AAA)
    * When playing back through the
    internal speaker with the medium
    volume level
    The battery life may shorten
    depending on the operation of the
    unit.
    Notes
    Do not use manganese batteries for
    this unit.
    When you replace the batteries with
    new ones, the clock setting display
    appears. In this case, set the date
    and time again. The recorded
    messages and alarm setting,
    however, will remain.
    When replacing the batteries, be
    sure to replace both batteries with
    new ones.
    • Do not charge dry batteries.
    When you are not going to use the
    unit for a long time, remove the
    batteries to prevent damage from
    battery leakage and corrosion.
    The unit is accessing data while
    “ACCESS“ appears in the display
    window or the OPR indicator
    flashes in orange. While accessing,
    do not remove the batteries. Doing
    so may damage the data.
    Clock setting display appears when you insert batteries for the first time, or when you replace the batteries with new ones. In
    this case, proceed from step 2.
    1
    Display the clock setting display.
    2
    Set the date.
    3
    Set the time.
    Step 2: Setting the Clock
    Recording Messages
    You can record up to 99 messages in each of the four folders (A, B, C, and D).
    Since a newly recorded message is automatically added behind the last recorded
    message, you can start recording quickly without searching for the end of the
    last recording.
    e.g. Message 1 Message 2 Newly recorded message Blank space
    Note
    Before making a long recording, be sure to insert new batteries and check the battery
    indicator.
    1
    Select the recording mode.
    See “Changing the Recording Mode” on the reverse side.
    2
    Select the folder.
    See “Selecting the Folder”.
    3
    Start recording.
    You do not need to keep pressing zXREC/PAUSE while recording.
    4
    Stop recording.
    If you do not change the folder after you stop recording, the next time you
    record you will record in the same folder.
    To Do this
    pause recording* Press zXREC/PAUSE.
    During recording pause, the OPR indicator flashes in
    red and “PAUSE” flashes in the display window.
    release pause and Press zXREC/PAUSE.
    resume recording Recording resumes from that point.
    (To stop recording after pausing recording, press
    xSTOP.)
    listen to the current Press xSTOP to stop recording, then press
    recording NxPLAY/STOP.
    review the current Press NxPLAY/STOP during recording.
    recording instantly
    search backward during Hold down – . during recording or recording
    recording (Review) pause. Recording mode will be released, and
    reviewing of the current recording starts. If you
    release the button, playback starts from that point.
    select the microphone You can select the microphone sensitivity using the
    sensitivity menu. See “Selecting the Microphone Sensitivity”.
    H (high): To record at meeting or in a quiet and/or
    spacious place.
    L (low): To record for dictation or in a noisy place.
    * About one hour after you pause recording, recording pause is automatically released
    and the unit goes into the stop mode.
    Selecting the Folder
    1 Press DISPLAY/MENU for more than 1 second until
    “MODE” appears in the display window.
    2 Press – . or >+ to select “FOLDER” and press
    NxPLAY/STOP.
    3 Press – . or >+ to select the folder you want
    and press NxPLAY/STOP.
    4 Press xSTOP to exit the menu mode.
    Current folder
    BBasic Operations
    Information
    IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT,
    INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
    NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY
    DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
    For the customers in the U.S.A.
    INFORMATION
    This equipment has been tested and found to comply with the
    limits for a Class B digital device, pursuant to Part 15 of the
    FCC Rules. These limits are designed to provide reasonable
    protection against harmful interference in a residential
    installation. This equipment generates, uses, and can radiate
    radio frequency energy and, if not installed and used in
    accordance with the instructions, may cause harmful
    interference to radio communications.
    However, there is no guarantee that interference will not occur
    in a particular installation. If this equipment does cause
    harmful interference to radio or television reception, which can
    be determined by turning the equipment off and on, the user is
    encouraged to try to correct the interference by one or more of
    the following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and
    receiver.
    Connect the equipment into an outlet on a circuit different
    from that to which the receiver is connected.
    Consult the dealer or an experienced radio/TV technician
    for help.
    You are cautioned that any changes or modifications not
    expressly approved in this manual could void your authority
    to operate this equipment.
    If you have any questions about this product, you may call:
    Sony Customer Information Services Center 1-800-222-7669 or
    http://www.sony.com/
    Declaration of Conformity
    Trade Name: SONY
    Model: ICD-P320
    Responsible Party: Sony Electronics Inc.
    Address: 16530 Via Esprillo, San Diego,
    CA 92127 U.S.A.
    Telephone Number: 858-942-2230
    This device complies with part 15 of the FCC Rules.
    Operation is subject to the following two conditions: (1)
    This device may not cause harmful interference, and (2)
    this device must accept any interference received,
    including interference that may cause undesired operation.
    Disposal of Old Electrical & Electronic
    Equipment (Applicable in the European Union
    and other European countries with separate
    collection systems)
    This symbol on the product or on its packaging
    indicates that this product shall not be treated
    as household waste. Instead it shall be handed
    over to the applicable collection point for the
    recycling of electrical and electronic equipment.
    By ensuring this product is disposed of
    correctly, you will help prevent potential
    negative consequences for the environment and
    human health, which could otherwise be caused by
    inappropriate waste handling of this product. The recycling of
    materials will help to conserve natural resources. For more
    detailed information about recycling of this product, please
    contact your local Civic Office, your household waste disposal
    service or the shop where you purchased the product.
    Note on recording
    Noise may be recorded if an object,
    such as your finger, etc., accidentally
    rubs or scratches the unit during
    recording.
    Maximum recording time
    The maximum recording time of all
    the folders is as follows. You can
    record messages for the maximum
    recording time in a single folder.
    HQ* 7 h. 20 min.
    SP** 19 h. 35 min.
    LP*** 32 h. 10 min.
    (h.: hours/min.: minutes)
    * HQ: High quality recording mode
    (monaural sound)
    ** SP: Standard play recording mode
    (monaural sound)
    ***LP: Long play recording mode
    (monaural sound)
    Notes
    To record in better sound quality,
    select the HQ mode. For switching
    the recording mode, see “Changing
    the Recording Mode” on the reverse
    side.
    Before making a long recording, be
    sure to check the battery indicator.
    The maximum recording time and
    the number of messages you can
    make vary depending on the
    conditions of use.
    When you record messages in the
    mixture of HQ, SP and LP mode, the
    maximum recording time will be
    between those for the HQ and LP
    modes.
    Due to the limitation of the IC
    recording system, this unit records
    in the minimum recording unit of
    approx. 2 seconds at most, therefore
    the following symptoms may occur:
    When a message is shorter than
    the minimum recording unit, it is
    still counted as approx. 2 seconds
    at most so the remaining
    recording time will decrease by
    more than the actual length of the
    message.
    When the message is longer than
    the minimum recording unit, the
    remaining recording time will
    decrease by more than the actual
    length of the message if it cannot
    be divided by the minimum
    recording unit without a
    remainder.
    The sum of the number on the
    counter (elapsed recording time)
    and the remaining recording time
    may be less than the unit’s
    maximum recording time.
    Remaining memory
    indication
    During recording, the remaining
    memory indicator decreases one by
    one.
    The memory is
    nearly full.
    Flashing
    When the remaining time of
    recording reaches 5 minutes, the
    last one of the indication flashes.
    If the remaining recording time
    display mode is selected, the
    remaining recording time display
    will also flash when the remaining
    time reaches 1 minute.
    When the memory is full, recording
    automatically stops and “FULL”
    will flash in the display window
    with an alarm sound. To continue
    recording, first erase some of the
    messages.
    Notes
    If you press zXREC/PAUSE when
    the memory is full, “FULL” will flash
    with an alarm sound. Erase some of
    the messages before you start
    recording again.
    If you press zXREC/PAUSE after
    you have recorded 99 messages,
    “FULL” will flash with an alarm
    sound. Select another folder or erase
    some of the messages.
    Starting recording
    automatically in response
    to the sound — Advanced
    VOR function
    When VOR (voice operated
    recording) is set to ON in the menu,
    recording starts when the recorder
    detects sound. (“VOR” is displayed
    in the display window.)
    Recording stops when no sound is
    heard. (“VOR PAUSE” flashes in
    the display window.)
    Note
    VOR function is affected by the sound
    around you. Set the microphone
    sensitivity to “H (high)” or “L (low)”
    using the menu. If recording is not
    satisfactory after you have changed
    the microphone sensitivity, or for
    important recording, set VOR to OFF.
    Playing Back Messages
    BGetting started
    Troubleshooting
    Before taking the unit for repair, check the following
    sections. Should any problem persist after you have
    made these checks, consult your nearest Sony dealer.
    The unit does not operate.
    The batteries have been inserted with incorrect
    polarity.
    The batteries are weak.
    The buttons are locked with the HOLD switch. (If
    you press any button, “HOLD” will flash three
    times.)
    No sound comes from the speaker.
    The ear receiver or headphones are plugged in.
    The volume is turned down completely.
    “FULL” is displayed and you cannot start
    recording.
    The memory is full. Erase some of the messages.
    99 messages have been recorded in the selected
    folder. Select another folder or erase some of the
    messages.
    Noise is heard.
    An object, such as your finger, etc., accidentally
    rubbed or scratched the unit during recording so
    that noise was recorded.
    The unit was placed near an AC power source, a
    fluorescent lamp or a mobile phone during
    recording or playback.
    Plug of the connected microphone was dirty when
    recording. Clean the plug.
    Ear receiver/headphones plug is dirty. Clean the
    plug.
    Recording level is low.
    Set the microphone sensitivity to “H (high)” using
    the menu.
    Recording is interrupted.
    The advanced VOR function is activated. Set VOR
    to “OFF”.
    Recording level is unstable (when recording
    music, etc.).
    This unit is designed to automatically adjust the
    recording level when recording meetings, etc., and
    is not suitable for music recording.
    “--Y--M--D” or “--:--” is displayed.
    You have not set the clock.
    “--Y--M--D” or “--:--” is displayed on the REC
    DATE display.
    The date and time of recording will not be
    displayed if you recorded the message when the
    clock was not set.
    You cannot divide a message.
    You cannot divide a message in a folder which has
    99 messages.
    If you divide messages frequently, the unit may
    become unable to divide a message.
    You cannot divide a message in the first or the last
    1 second of a message.
    You cannot record messages up to the
    maximum recording time.
    If you record messages in a mixture of HQ, SP and
    LP modes, the recordable time varies from the
    maximum HQ mode recording time to the
    maximum LP mode recording time.
    No more recording can be made when 99 messages
    each have been recorded in a folder.
    Due to the limitation of the IC recording system,
    this unit records in the minimum recording unit. If
    the length of each message cannot be divided by
    the minimum recording unit, the remaining
    recording time may decrease by more than the
    total length of the messages.
    The remaining time displayed in the display
    window is shorter than that displayed in
    the supplied “Digital Voice Editor“ software.
    The unit requires a certain amount of memory for
    system operation. That amount is subtracted from
    the remaining time, which is the reason for the
    difference.
    The unit does not operate correctly.
    Take out the batteries and insert them again.
    Please note that recorded messages may be erased
    during service or repair work.
    Playing back a message
    repeatedly
    — Repeat Play
    During playback, press
    NxPLAY/STOP for more than
    one second.
    “ will be displayed and the
    selected message will be played
    back repeatedly.
    To resume normal playback, press
    NxPLAY/STOP again. To stop
    playback, press xSTOP.
    Playing back all messages
    in a folder continuously
    — Continuous Play
    You can select the continuous play
    mode with the CONT in the menu.
    When you set CONT to ON, you
    can play back all messages in a
    folder continuously.
    Searching forward/
    backward during playback
    (Cue/Review)
    To search forward, keep >+
    pressed during playback and
    release the button at the point you
    wish to resume playback.
    To search backward, keep – .
    pressed during playback and
    release the button at the point you
    wish to resume playback.
    If you keep >+ or – .pressed,
    the unit starts to search at higher
    speed.
    For the first 7 seconds of cue/
    review, fast playback sound can be
    heard. When searching at a higher
    speed, playback sound will not be
    heard.
    During cue/review, the counter
    will be displayed, regardless of the
    display mode setting.
    1
    Tip
    When fast playback is done to the end
    of the last message, “END” flashes 5
    times. (You cannot hear the playback
    sound.) If you keep – . pressed
    while “END” is flashing, the messages
    are played back rapidly, and normal
    playback will start at the point you
    release the button.
    When “END” stops flashing and the
    OPR indicator goes off, the unit will
    stop at the beginning of the last
    message.
    If the last message is long and you
    wish to start playback at a later part of
    the message, keep >+ pressed to
    play back the message to the end and
    then press – . while “END” is
    flashing to go back to the desired
    point.
    (For messages other than the last one,
    go to the beginning of the next
    message and play backward to the
    desired point.)
    Locating quickly the point
    you wish to start playback
    (Easy Search)
    When EASY-S is set to “ON” in the
    menu, you can advance approx. 10
    seconds by pressing >+. This
    function is useful when locating a
    desired point in a long recording.
    (“EASY-S” is displayed in the display
    window.)
    Make sure to insert both
    of the batteries from
    their – ends.
    Printed on 100% recycled
    paper using VOC (Volatile
    Organic Compound)-free
    vegetable oil based ink.
    Selecting the Microphone Sensitivity
    1 Press DISPLAY/MENU for more than 1 second until
    “MODE” appears in the display window.
    2 Press – . or >+ to select “SENS” and press
    NxPLAY/STOP.
    3 Press – . or >+ to select “H (high sensitivity)”
    or “L (low sensitivity)” and press NxPLAY/STOP.
    4 Press xSTOP to exit the menu mode.
    If the battery compartment lid is
    accidentally detached, attach it as
    illustrated.
    Press – . or >+ to
    display the desired
    message number.
    >+: for larger
    message number
    .: for smaller
    message number
    Counter
    display*
    Selected message number
    Number of
    messages in
    a folder
    1 Press zXREC/PAUSE.
    * The display selected
    with the DISPLAY/
    MENU button
    appears.
    Current message
    number
    Counter display*
    2 Speak to the
    built-in
    microphone.
    OPR indicator
    (lights in red during
    recording.)
    Remaining memory
    indicator
    Recording mode
    Press xSTOP.
    The unit stops at the
    beginning of the current
    recording.
    NxPLAY/STOP
    .(Review)
    zXREC/PAUSE
    2 Press NxPLAY/STOP.
    The month digits will flash.
    3 Set the month and day in
    sequence, then press NxPLAY/
    STOP.
    The hour digits will flash.
    1 Tip
    To set the date to Year 2006, display “06Y”.
    1 Press – . or >+ to select
    the digits of the year.
    2 Adjust the volume
    with the VOL control.
    i (earphone) jack
    1 Press NxPLAY/STOP.
    Counter display (or the
    selected display mode)
    xSTOP
    OPR indicator
    (lights in green during
    playback.)
    2 Press – . or >+ to display
    “SET DATE”.
    3 Press NxPLAY/STOP.
    The year digits will flash.
    1 Press DISPLAY/MENU for more
    than 1 second until “MODE”
    appears in the display window.
    The unit enters the menu mode.
    1 Tip
    This unit does not have a power on/off switch. The display is shown at all times.
    3 Set the minute.
    4 Press NxPLAY/STOP at the time
    signal.
    The display will return to “SET
    DATE”.
    5 Press xSTOP to exit from the
    menu mode.
    If the unit is left unused for more
    than 3 seconds in the stop mode, the
    display will show the current time.
    1 Press – . or >+ to select
    the digits of the hour.
    2 Press NxPLAY/STOP.
    The minute digits will flash.
Sony ICD-P320

Potrzebujesz pomocy?

Liczba pytań: 2

Czy masz pytanie dotyczące Sony ICD-P320 lub potrzebujesz pomocy? Zadaj pytanie tutaj. Podaj jasny i wyczerpujący opis problemu oraz pytanie. Im więcej szczegółów swojego problemu i pytania podasz, tym łatwiej będzie innym właścicielom Sony ICD-P320 poprawnie odpowiedzieć na Twoje pytanie.

hENRYK, 2017-04-13 09:09:27 Bez komentarza

szanowni Pąństwo, poszukuję instrukcji do ICD -P620. Proszę o pomoc. Z przyjaznym pozdrowieniem HBz

Odpowiedz na to pytanie
Robert, 2016-11-29 18:32:11 Bez komentarza

Witam mam dyktafon sony ICD-P320 straciłem gdzieś płytę z oprogramowaniem. Mam pytanie czy można z jakiejś strony waszej firmy Sony zciągnąć sobie te oprogramowanie ale teraz mam windowsa 8,1 i na drugim laptopie windows 7. a ten dyktafon mam od paru lat .

Odpowiedz na to pytanie

Tu możesz bezpłatnie wyświetlić instrukcję dotyczącą Sony ICD-P320. Ta instrukcja należy do kategorii Dyktafony i otrzymała oceny od 1 osób ze średnią 5.8. Ta instrukcja jest dostępna w następujących językach: Angielski. Czy masz pytanie dotyczące Sony ICD-P320 lub potrzebujesz pomocy? Zadaj pytanie tutaj

Specyfikacje Sony ICD-P320

Marka Sony
Model ICD-P320
Produkt Dyktafon
Język Angielski
Typ pliku PDF
Audio
Maksymalny czas nagrywania 7.3godz.
Zasięg częstotliwości 260 - 6800Hz
Pozostałe funkcje
Wymiary produktu (SxGxW) 34.6 x 18 x 109.5mm
Rodzaj baterii AAA
Waga i rozmiary
Waga produktu 680g
Oprogramowanie
Dołączone oprogramowanie Digital Voice Editor Ver.2
Pamięć
Pojemność pamięci wewnętrznej 64MB
Bateria
Czas pracy na zasilaniu akumulatorowym 22godz.
Głośniki
Średnica głośników 28mm
Moc wyjściowa 250mW

Powiązane instrukcje produktów

Dyktafon Sony

Ta strona korzysta z ciasteczek aby świadczyć usługi na najwyższym poziomie. Dalsze korzystanie ze strony oznacza, że zgadzasz się na ich użycie.

Dowiedz się więcej