Instrukcja obsługi Honeywell RTH230B

Honeywell RTH230B
9.2 · 2
PDF instrukcja
 · 4 str.
Angielski
instrukcjaHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Tu możesz bezpłatnie wyświetlić instrukcję dotyczącą Honeywell RTH230B. Ta instrukcja należy do kategorii termostaty i otrzymała oceny od 2 osób ze średnią 9.2. Ta instrukcja jest dostępna w następujących językach: Angielski. Czy masz pytanie dotyczące Honeywell RTH230B lub potrzebujesz pomocy? Zadaj pytanie tutaj

Potrzebujesz pomocy?

Masz pytanie dotyczące Honeywell , a w instrukcji nie ma odpowiedzi?

  • Otrzymuj aktualizacje dotyczące rozwiązań
  • Uzyskaj odpowiedzi na swoje pytania

Pytanie i odpowiedź

Liczba pytań: 0

Termostat Honeywell RTH230B to urządzenie do regulacji temperatury w pomieszczeniach. Posiada prostą i intuicyjną obsługę dzięki łatwemu w użyciu panelowi sterowania. Termostat automatycznie reguluje temperaturę w sposobie, który pozwala zaoszczędzić na rachunkach za energię elektryczną, a jednocześnie zapewnia komfort użytkowania. Można programować temperatury na 7 dni w tygodniu, a także ustawić różne temeperatury dzienne i nocne. Ponadto, termostat posiada funkcję automatycznego odcinania zasilania oraz pamięć ustawień w przypadku przerwy w dostawie energii elektrycznej. RTH230B ma przełącznik trybu pracy, który pozwala wybrać pomiędzy trybem grzania a chłodzenia, co sprawia, że jest to uniwersalne urządzenie mogące być stosowanym w różnych typach pomieszczeń. Dzięki funkcji szybkiego montażu, Honeywell RTH230B może być łatwo zainstalowany w różnych typach systemów grzewczych i klimatyzacyjnych.

Ogólne
MarkaHoneywell
ModelRTH230B
Produkttermostat
JęzykAngielski
Typ plikuInstrukcja obsługi (PDF)

Nie możesz w instrukcji znaleźć odpowiedzi na swoje pytanie? Odpowiedź na pytanie dotyczące modelu Honeywell RTH230Bmożesz być dostępna w sekcji FAQ poniżej.

Gdzie najlepiej umieścić termostat?

Najlepszym miejscem do umieszczenia termostatu jest pomieszczenie, w którym spędzasz najwięcej czasu. Zwykle jest to salon lub kuchnia. Umieść termostat około półtora metra nad podłogą. Miejsce nie powinno być bezpośrednio nasłonecznione ani położone na ścianie zewnętrznej.

Czemu służy martwa strefa termostatu?

Jeśli termostat ma martwą strefę, oznacza to, że czasami instalacja jest w stanie spoczynku. Termostat włącza się tylko wtedy, gdy różnica jest większa niż np. 2˚C od temperatury ustawionej dla danego pomieszczenia.

Jaka jest najlepsza temperatura w pomieszczeniu?

Większość ludzi uważa, że idealna temperatura w pomieszczeniu wynosi od 19 do 22 stopni Celsjusza.

Czy instrukcja obsługi Honeywell RTH230B jest dostępna w języku Polski?

Niestety nie posiadamy instrukcji obsługi Honeywell RTH230B dostępnej w języku Polski. Ta instrukcja jest dostępna w języku Angielski.

Twojego pytania nie ma na liście? Zadaj pytanie tutaj

Brak wyników