Casio EQW-500BE-1AVER

Instrukcja obsługi Casio EQW-500BE-1AVER

(1)
  • Operation Guide 5041
    1
    MO0806-EA
    Getting Acquainted
    Congratulations upon your selection of this CASIO watch. To get the most out of your
    purchase, be sure to read this manual carefully.
    Starting second hand movement and digital display
    To conserve battery power, the watch is shipped from the
    factory with its functions disabled. Pressing any one of the
    watch’s three buttons will activate its functions, which will
    cause the second hand to start moving and the digital
    display to activate.
    Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
    or loss suffered by you or any third party arising through the use of this product or
    its malfunction.
    About This Manual
    Button operations are indicated using the letters shown
    in the illustration.
    Each section of this manual provides you with the
    information you need to perform operations in each
    mode. Further details and technical information can be
    found in the “Reference” section.
    Hour hand
    Minute hand
    Date
    Second hand
    (Timekeeping/
    Stopwatch)
    24-hour hand
    Stopwatch
    minute hand
    Stopwatch second hand
    Hand Setting Mode Alarm Mode
    World Time Mode
    General Guide
    Press C to change from mode to mode.
    About one or two seconds after you enter the World Time Mode, Alarm Mode, or
    Hand Setting Mode, the hands will move to the position that indicates the current
    setting of the mode.
    In the Timekeeping Mode (except when a setting screen is on the display), press B
    to illuminate the face of the watch for about one second.
    Timekeeping Mode
    Press C.
    Stopwatch Mode
    Radio-controlled Atomic Timekeeping
    This watch receives a time calibration signal and updates its time setting accordingly.
    Supported time calibration signals: Germany (Mainflingen), England (Anthorn).
    See the information under “Signal Reception Troubleshooting” if you experience
    problems with time calibration signal reception.
    Current Time Setting
    This watch adjusts its time setting automatically in accordance with a time calibration
    signal. You also can perform a manual procedure to set the time and date, when
    necessary.
    The first thing you should do after purchasing this watch is to specify your
    Home City, which is the city where you normally will use the watch. For more
    information, see “To specify your Home City”.
    When using the watch outside the areas covered by the time signal transmitters, you
    will have to adjust the current time setting manually as required. See
    “Timekeeping”
    for more information about manual time settings.
    To specify your Home City
    1. In the Timekeeping Mode, hold down A for about five
    seconds until the watch beeps twice.
    The second hand will move to the city code of the
    currently selected Home City. This is the city code
    setting mode.
    2. Use B to move the second hand to the city code you
    want to use as your Home City.
    Each press of B causes the second hand to advance
    clockwise to the next city code.
    Time calibration signal reception is supported when
    any one of the city codes shown in the table below is
    selected as your Home City.
    Second hand
    City code
    For full information on city codes, see the “City Code Table”.
    In addition to the above, you also can select city codes that are outside the ranges
    of the time calibration signal transmitters supported by this watch.
    3. After the Home City setting is the way you want, press A to return to the
    Timekeeping Mode.
    Normally, your watch should show the correct time as soon as you specify your
    Home City code. If it does not, it should adjust automatically after the next auto
    receive operation. You also can perform manual receive or you can set the time
    manually.
    German/U.K. Signal
    City Code
    LON
    PA R
    ATH
    City Name
    London
    Paris
    Athens
    Even if the time calibration signal is received correctly, there are some times when
    the analog hands may not indicate the correct time. If this happens, use the
    procedures under “Adjusting the Home Positions” to check the home positions of the
    hands, and make adjustments as required.
    Time Calibration Signal Reception
    There are two different methods you can use to receive the time calibration signal:
    auto receive and manual receive.
    Auto Receive
    With auto receive, the watch receives the time calibration signal automatically up to six
    times a day. When any auto receive is successful, the remaining auto receive
    operations are not performed. For more information, see “About Auto Receive”.
    Manual Receive
    Manual receive lets you start a time calibration receive operation with the press of a
    button. For more information, see “To perform manual receive”.
    12 o’clock
    or
    Important!
    When getting ready to receive the time calibration signal, position the watch as
    shown in the nearby illustration, with its 12 o’clock side facing towards a window.
    This watch is designed to receive a time calibration signal late at night. Because of
    this, you should place the watch near a window as shown in the illustration when you
    take it off at night. Make sure there are no metal objects nearby.
    Make sure the watch is facing the right way.
    Proper signal reception can be difficult or even impossible under the conditions listed
    below.
    Signal reception normally is better at night than during the day.
    Time calibration signal reception takes from two to seven minutes, but in some
    cases it can take as long as 14 minutes. Take care that you do not perform any
    button operations or move the watch during this time.
    Inside or
    among
    buildings
    Inside a
    vehicle
    Near a
    construction
    site, airport,
    or other
    sources of
    electrical
    noise
    Near high-
    tension power
    lines
    Among or
    behind
    mountains
    Near
    household
    appliances,
    office
    equipment,
    or a mobile
    phone
    Approximate Reception Ranges
    Anthorn
    Mainflingen
    500 kilometers
    1,500 kilometers
    U.K. signal transmitter
    approximate reception
    range as of April 2007
    In April 2007, the U.K. signal transmitter was moved from Rugby to Anthorn, which
    resulted in a slight shift in the approximate reception range of the signal. The shift is
    so slight that there is virtually no change in the ability to receive the signal.
    Even when the watch is within the reception range of a transmitter, signal reception
    may be impossible at times due to the effects of geographic contours, structures,
    weather, the season of the year, the time of day, radio interference, etc. Note that the
    signal becomes weaker at distances of approximately 500 kilometers from the
    transmitter, which means that the influence of the conditions listed above becomes
    even greater.
Casio EQW-500BE-1AVER

Potrzebujesz pomocy?

Liczba pytań: 1

Czy masz pytanie dotyczące Casio EQW-500BE-1AVER lub potrzebujesz pomocy? Zadaj pytanie tutaj. Podaj jasny i wyczerpujący opis problemu oraz pytanie. Im więcej szczegółów swojego problemu i pytania podasz, tym łatwiej będzie innym właścicielom Casio EQW-500BE-1AVER poprawnie odpowiedzieć na Twoje pytanie.

Krzysztof, 2017-09-08 15:41:12 Bez komentarza

Potrzebuje instrukcji w języku Polskim .Po wyminie baterii źle chodzi . Pozdrawiam

Odpowiedz na to pytanie

Tu możesz bezpłatnie wyświetlić instrukcję dotyczącą Casio EQW-500BE-1AVER. Ta instrukcja należy do kategorii Zegarki i otrzymała oceny od 1 osób ze średnią 6.1. Ta instrukcja jest dostępna w następujących językach: Angielski. Czy masz pytanie dotyczące Casio EQW-500BE-1AVER lub potrzebujesz pomocy? Zadaj pytanie tutaj

Specyfikacje Casio EQW-500BE-1AVER

Ogólne
Marka Casio
Model EQW-500BE-1AVER
Produkt Zegarek
Język Angielski
Typ pliku PDF
Szczegóły Techniczne
Stoper
Funkcja world time
Funkcja alarmu
Kalendarz
Podświetlenie LED
Odbiornik sygnału radiowego DCF/MSF
Wodoodporny do 100m
Konstrukcja
Typ szkła mineral
Materiał obudowy stainless steel
Tworzywo paska resin
Moc
Rodzaj baterii CR1616
Czas eksploatacji baterii 2rok/lata
Liczba baterii 1
Pozostałe funkcje
Wymiary produktu (SxGxW) 46 x 13.7 x 49mm
Waga i rozmiary
Waga produktu 91.8g

Często zadawane pytania

Poniżej znajdziesz najczęściej zadawane pytania dotyczące: Casio EQW-500BE-1AVER.

Twojego pytania nie ma na liście? Zadaj pytanie tutaj

InstrukcjaObslugiPDF.pl

Szukasz instrukcji? InstrukcjaObslugiPDF.pl zapewnia, że szybko znajdziesz instrukcję, której szukasz. Nasza baza danych zawiera ponad milion instrukcji PDF od ponad 10 000 marek. Codziennie dodajemy najnowsze instrukcje, abyś zawsze znalazł produkt, którego szukasz. To bardzo proste: po prostu wpisz nazwę marki i rodzaj produktu w pasku wyszukiwania, a od razu będziesz mógł przejrzeć instrukcję online za darmo.

InstrukcjaObslugiPDF.pl

© Copyright 2020 InstrukcjaObslugiPDF.pl. Wszystkie prawa zastrzeżone.

Ta strona korzysta z ciasteczek aby świadczyć usługi na najwyższym poziomie. Dalsze korzystanie ze strony oznacza, że zgadzasz się na ich użycie.

Dowiedz się więcej