Instrukcja obsługi Bosch WAB20060SN

Zobacz tutaj bezpłatnie instrukcję Bosch WAB20060SN. Przeczytałeś instrukcję, ale czy odpowiada ona na twoje pytanie? Zadaj pytanie innym użytkownikom Bosch WAB20060SN na tej stronie.

1
Safety instructions
The washing machine is heavy - take care when lifting.
Caution: frozen hoses may rip/burst. Do not install the washing machine in areas exposed
to frost or outdoors.
The washing machine could be damaged. Do not lift the appliance by protruding
components (e.g. the washing machine door).
In addition to the instructions provided in this document, special regulations from the
relevant water and electric utility companies may apply.
If in doubt, have a technician connect the appliance.
Lay hoses and cables in such a way that there is no risk of tripping.
Scope of delivery depending on model
Also required, depending on the connection:
1 hose clamp Ø 24-40 mm (exclusive dealers) to connect to a siphon
a page 4; water connection.
Useful tools
Spirit level for installation.
Spanner WAF 13 for undoing the transport safety bolts --> page 3 and
Spanner WAF 17 for levelling the appliance feet --> page 5.
Installation surface
The machine must be stable so that it does not move around.
The installation surface must be firm and level.
Soft floors/floor coverings are not suitable.
Installation on a pedestal
The feet of the washing machine must be secured with holding brackets*.
* order no. WMZ2200, WX9756, CZ110600, Z7080X0
Installation on a wood joist floor
If possible, place the washing machine in a corner.
Screw a water-resistant wooden board (min. 30 mm thick) to the floor.
The feet of the washing machine must be secured with holding brackets*.
* order no. see above.
Mains cable
Water outlet
Water inlet
Elbow
for fixing the drainage
hose in place
Covers
A
quaä
St
op
A
quaä
S
ecure
St
an
d
ar
d
Wrench
(depending on model)
Moisture inside the drum is
due to final testing.
2
Hose and cable lengths depending on model
Left-hand connection
or
Right-hand connection
Available from specialist dealers/the after-sales service:
Extension for Aqua-Stop or cold-water inlet hose (approx. 2.50 m).
order no. WMZ2380, WZ10130, CZ11350, Z7070X0
Longer inlet hose (approx. 2.20 m) for standard model.
Installing the appliance depending on model
Install the appliance before connecting it to the power supply.
Risk of electric shock.
For models with a continuous appliance covering plate or a square service flap, the
appliance covering plate can be replaced by a metal cover.
Instead of the appliance covering plate, you must have a metal cover fitted by an expert.
For models with a non-continuous appliance covering plate or a round service flap, the
appliance covering plate must not be removed.
Only install the washing machine underneath a continuous worktop that is securely
connected to adjacent cabinets.
Recess width of 60 cm required.
~
145 cm
~
100 cm
~
95 cm
~
135 cm
~
145 cm
min. * cm
~
85 cm
max. 100 cm
3
Removing the transport braces
Before using the appliance for the first time, make sure that you
completely remove transport braces and keep them for subsequent
transportation.
If you need to transport the appliance at a later date, always re-affix the
transport braces to prevent damage to the machine a page 6.
Store the screw and sleeve screwed together.
1. Take the hoses and elbow out of the holders, depending on model.
2. Loosen the bolts ....
... until they move freely in the sleeves.
3. Completely remove all 4 transportation protection devices and take the main cable out of the
holder.
4. Insert covers.
4
Water connection depending on model
Risk of electric shock. Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).
To prevent leaks or water damage, observe the instructions in this
section.
Caution: only operate the washing machine using cold drinking water.
Do not connect to the mixer tap of an unpressurised hot-water boiler.
Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
If in doubt, have a technician connect the appliance.
Water inlet
Water inlet hose:
Caution: do not bend, squash, modify or cut through
(otherwise its strength is no longer guaranteed).
Optimum water pressure in the supply network: 100ä1,000 kPa (1ä10 bar)
When the tap is on, the water flow is at least 8 l/min.
If the water pressure is higher than this, a pressure reducing valve must be installed.
Model: AquaäStop
AquaäSecure
Standard
1. Connect the water inlet hose to the tap.
Caution: only tighten the screw connections by
hand.
2. Open the water tap carefully, checking the leak
tightness of the connection points.
Caution: the screw connection is under mains water
pressure.
Water outlet
Water outlet hose:
Caution: do not bend or pull lengthways.
Height difference between the installation surface and the drain:
min. 60 cm - max. 100 cm
Outlet in a sink
Caution: secure the drain hose from slipping out.
Caution: the plug must not block drainage from the sink. During
pumping, check whether the water is draining away quickly enough.
The end of the drain hose must not be immersed in the water pumped
out. This risks water being sucked back into the washing machine.
Drainage into a siphon:
Caution: the connection point must be secured with a hose clamp,
Ø 24-40 mm (exclusive dealers).
max.
90°
max.
90°
min.
10 mm
min.
10 mm
3/4”
3/4”

Zadaj pytanie

Zadaj tutaj pytanie dotyczące Bosch WAB20060SN innym właścicielom produktu. Podaj jasny i wyczerpujący opis problemu i swoje pytanie. Im lepiej opisany jest twój problem i pytanie, tym łatwiej innym właścicielom Bosch WAB20060SN udzielić ci dobrej odpowiedzi.

Specs

Marka Bosch
Model WAB20060SN
Produkt Pralka
EAN 4242002705149
Język Angielski
Grupa produktu Pralki
Typ pliku PDF
Design
Model Wol✗stojący
Kolor produktu Biały
Typ ładowania Od przodu
Wbudowany wyświetlacz
Typ wyświetlacza LED (Dioda elektroluminescencyjna)
Zawias drzwiczek Left
Kąt otwierania drzwi 140°
Kolor drzwiczek Biały
Technologia napędu bezpośredniego (inwertor) -
Typ kontroli Buttons, Rotary
Praca
Pojemność bębna 5.5kg
Maksymalna prędkość obrotu 1000RPM
Kategoria prania -
Klasa wirowania (suszenia) -
Ilość programów piorących -
Poziom hałasu (pranie) 59dB
Czas cyklu (max) 180min
Opóźniony start czasomierza -
Poziom hałasu (wirowanie) 73dB
Pozostała wilgoć 67%
- Delicate/silk, Quick
Programy zmywania
Pół wsadu -
Program prania dla alergików
Czarny program prania
Program do prania delikatnych tkanin/jedwabiu
Krótki program prania
Zarządzanie energią
Klasa wydajności energetycznej A+
Pranie zużywające energię 0.87kWh
Pobór wody na cykl -L
Certyfikat EnergyStar -
Roczne zużycie energii pranie 182kWh
Roczne zużycie wody pranie -L
Waga i rozmiary
Szerokość produktu -mm
Długość urządzenia -mm
Wysokość urządzenia -mm